The Fundamentals of Plumbing Knowledge When Installing a Bathtub
Schedule Free EstimateHow do you really feel when it comes to How to Install a Bathtub Yourself?
Setting up a tub isn't specifically rocket science, but it does need solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old bath tub with a new one is additionally a reasonably challenging job. If the old bathtub is easily easily accessible, the task can move easily; if you need to open up a wall to remove the old bathtub and also place the new tub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly require a helper to leave the old tub as well as set in the new one. Ensure you have actually qualified on your own for the job as well as fit attempting it. Rather than employing a contractor to take over a halfway-completed job, it is much better to think about utilizing one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This write-up will certainly assist you mount a brand-new bathtub in your bathroom if you have actually already gotten a new bathtub and also do not require to change the plan of your previous supply of water pipes.
Your tools and also material list must make up the following:
Getting ready for the Installation
To start with, the supporting framework supplied with the bathroom needs to be fitted (if needed) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to ensure that if the faucet features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps device to stop pressure on the tub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its final setting.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is detach the water supply. After doing so, switch on the faucets to drain any water staying in the system. The process of getting rid of the existing faucets can be fairly bothersome as a result of the limited accessibility that is usually the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. When the supply pipelines have been eliminated, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from turning during this procedure. When the taps have been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing substance.
Before carrying on to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Tub
Using both wood boards under its feet, put the bathtub in the called for setting. The wooden boards are useful in evenly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to ensure that the tub is leveled all round. This can be achieved by examining the spirit level as well as readjusting the feet on the tub until the level reads degree.
To mount faucets, fit the bottom of the furthest adaptable faucet port to the proper supply pipe by making a compression sign up with; after that do the very same for the other tap.
Activate the water supply and inspect all joints as well as new pipework for leaks as well as tighten them if needed. Fill up the tub as well as likewise inspect the overflow outlet and the normal electrical outlet for leakages.
Ultimately, take care of the bath paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bathtub needs to wait up until the bathtub has actually been utilized at least when as this will resolve it into its last setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin making certain that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier given backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former kind ought to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture a rigid seal, causing the water to penetrate the wall in between the bathroom as well as the tiling, leading to problems with wetness as well as possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your components as well as installations. They are marketed in tubes and cartridges, and can securing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealer can crack relatively very early if you do not take into account this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly offered on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were made aware of that report on How to Install a Bathtub Yourself from an acquaintance on our other blog. Are you aware of somebody who is inquisitive about the niche? Do not hesitate to promote it. We treasure reading our article about How to Install a Bathtub.
We're your answer!